EPISODE CLINIC
Ko
KoKoChChEnEnJaJaTwTwArArThTh

InMode Forma

InMode FORMA

InMode FORMA
#elasticity #SkinTexture #NoPain

Warms the dermis and maintains that temperature.

InMode FORMA

InMode Forma

InMode FORMA is a treatment that delivers heat to the dermis layer using bipolar radiofrequency . The dermis is heated to a desired temperature, and the treatment is performed while maintaining that temperature for a certain period of time .

During this process, collagen responds to the heat, and as regeneration follows, you can expect gradual improvements in skin texture and elasticity. It is not a treatment that produces dramatic results in a single session, but rather treatment that improves little by little with repeated treatments .

The FX version of the same InMode device has a different purpose. FX is used to reduce volume in areas with excess fat, while InMode FORMA is used to improve skin elasticity and texture .

InMode FORMA does not involve the process of strongly pulling tissue with negative pressure , and there is almost no downtime after the treatment , so you can receive it without any burden.

Loading treatment information.

Why InMode Forma

Even after reaching the target temperature
It maintains the heat for a while.

InMode FORMA sufficiently heats the dermis layer to the target temperature, and then
The treatment is performed while monitoring the skin temperature to maintain that temperature.

Point 01

Almost no heat reaches the fat layer.
Heat accumulates in the dermis layer.

InMode FORMA uses a bipolar radio frequency method, where high frequency flows between two electrodes inside the applicator. The energy does not spread deeply but reaches the dermis layer of the skin Heat mainly accumulates. So, I use it when I want to improve my skin texture and elasticity.

  • Bipolar high frequency — a method in which current flows only between two electrodes
  • Output frequency 1 MHz — Heats the dermis to the target temperature
  • No negative pressure — Does not suck up tissue, leaving no bruises or suction marks
Bipolar radiofrequency, current remaining in the dermis InMode FORMA Applicator epidermis dermis fat layer The depth to which the current reaches is up to half the distance between the electrodes. Almost no heat is transferred to the fat layer underneath.
Surface temperature upper limit (maximum 43 degrees) temperature treatment time Target temperature range Time to maintain temperature Automatically lowers output when reached the upper limit. Measure temperature, impedance, and contact status 10 times per second

Point 02

After raising it to the target temperature,
We proceed while maintaining that temperature.

Throughout the treatment , skin surface temperature, tissue impedance, and applicator contact status are checked 10 times per second. It automatically lowers the output when the temperature reaches the upper limit, and raises it again when it drops. Adjusts so as not to exceed the target temperature range.

  • Acquire

    Reach temperature

    Step of raising the dermis layer to the target temperature range

  • Control

    Temperature management

    Adjust output while monitoring temperature and impedance to ensure it does not exceed the upper limit.

  • Extend

    Secure time

    A step that continues heat for the required amount of time while maintaining the target temperature.

InMode Line-up

Elasticity and fat issues
The treatment methods are different.

Even with the same InMode equipment, depending on which applicator is used
The parts where energy is applied and its use change.

bipolar high-frequency applicator

InMode FORMA

InMode Forma

  • elasticityLift to improve skin texture and sagging
  • Can be applied to the entire face that needs elasticity.
  • Heating the dermis to a target temperature and maintaining that temperature
  • Relatively less pain and recovery burden due to the absence of negative pressure

Sound pressure, high frequency, high voltage pulse

InMode FX

InMode FX

  • provinceReduce it to refine the lower face line.
  • Areas caused by volume, such as a double chin and deep cheek
  • Grasp tissue with negative pressure and deliver 1 MHz high frequency and high voltage pulses
  • Suction marks and bruising may remain, so please consider the recovery period.

If you excessively reduce fat in a face where sagging is the main issue, it may actually make it look sunken.
Conversely, in areas with a lot of fat, simply increasing elasticity may not be enough to sufficiently refine the facial contours.
Therefore, we determine the necessary treatment and sequence by examining skin thickness, degree of sagging, and amount of fat together.

How It Works

InMode FORMA Working Principle

1

High frequency flows between the electrodes
Heat accumulates in the dermis layer

Bipolar radiofrequency transmission
2

Reach the target temperature range and
Maintain that temperature at a constant

Maintain target temperature Adjust within a maximum limit of 43 degrees
3

Collagen contracts and
It was newly created over the next few weeks.

sagging collagen Contraction and regeneration

Treatment Areas

InMode FORMA treatment area

Divide the face into sections,
Insert the appropriate energy into each zone.

InMode FORMA treatment Range
side cheek
front cheekbone, front cheek
nasolabial folds
jawline
double chin

Recommended For

I recommend this to people like this.

The facial contours are not as good as before
Those who feel it is not clear

The skin is thin and has fine wrinkles
Someone who is concerned

Lifting treatment
First-time experience

Without a recovery period
For those who want to maintain their daily routine

Doctor's Column

Treatment Stories written personally by the Director

This is a text written directly by the Director who actually performs this treatment , detailing the principles and standards.

Not only the results, but even the difference in experience

The Episode Difference

Why It's Different

Every process has its own reason for the EPISODE.

01

Starting with the cause of sagging
I will check.

Pre- treatment facial analysis

There is a difference between skin that looks sagging due to looseness and skin that looks heavy due to fat.
During the consultation, we assess skin elasticity and the amount of fat together to first determine if the area requires InMode FORMA.

ANALYSIS

02

In the EPISODE Lifting Design Guide
We will proceed accordingly.

EPISODE Lifting Design Guide

Dividing the mid and lower facial areas into 11 zones, and the areas prone to sinking and sagging The treatment is performed according to the separately indicated EPISODE Lifting Design Guide. The red boxes are the sinking areas, and the blue boxes are the sagging areas.

  • 01 Under the eyes
  • 02 Eye area
  • 03 nasolabial folds
  • 04 front cheekbone
  • 05 Side cheekbones
  • 06 Front ball
  • 07 Side ball
  • 08 deep cheek
  • 09 Jawline
  • 10 front double chin
  • 11 Side double chin
DESIGN

03

InMode FORMA is
It is based on the total amount of energy input.

treatment based on total amount of delivered energy

You cannot determine the actual energy injected into the skin based solely on the treatment area or time. So, the EPISODE is the total amount of energy actually transferred (kJ, Kilojoule). We determine the price in advance and perform the treatment according to that value.

ENERGY

04

If you keep a record
The changes are more visible.

Online treatment Report

The attending physician's comments on the treatment on that day, treatment details, and remaining number of treatment I will leave you an online report so you can view past records anytime. You can check.

RECORDS

Care Process

InMode FORMA proceeds through this process.

01

Cleansing

02

Check the treatment site

03

treatment

04

Soothing ampoule pack provided

05

homecoming

06

Provision of treatment report

Some processes will be changed for the promotional treatment.

Notice

Instructions for treatment

  • 1

    A warm sensation will persist during the treatment . Since this is a treatment that maintains a target temperature, it is normal to feel heat continuously, but if it feels too hot, please do not endure it and let us know immediately.

  • 2

    You may experience facial redness and a slight warmth immediately after the treatment , but these usually subside within a few hours. You can wash your face and apply basic makeup on the same day.

  • 3

    Please avoid saunas, steam rooms, hot baths, alcohol, and strenuous exercise on the day of the treatment . Redness and swelling may persist for a long time.

  • 4

    Your skin may become dry for a few days after the treatment . Please pay attention to moisturizing and sun protection.

  • 5

    Since it takes time for new collagen to be produced, changes may appear a few weeks after the treatment. It is usually repeated several times at one-month intervals, and the timing and extent of changes vary from person to person.

  • 6

    Please be sure to inform us before the treatment if you have metal implants in the treatment area, are pregnant, or if there is a possibility of pregnancy.

  • 7

    If you have a history of previous treatment such as fillers, Botox, or thread lifting, please inform us of the treatment area and time. We will adjust the order and scope of the treatment accordingly.